User Profile

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

RCS

Advanced Collector

Last Activity: Today, 11:00 AM

Joined: 06-24-2015

Location: USA

RCS replied to What a Winchester Weekend!

in Gas Trap & Pre-war Garands

Today, 11:00 AM
Scott, here is some basic data for Dec 41/ Jan 42 WRA rifles

Bolt w/round firing pin, op rod D35382-W.R.A. slant cut without relief cut,...

See more | Go to post
Leave a comment:
RCS replied to What an old fart makes for himself

in Garand Discussion Area

Yesterday, 09:08 AM
There were some cherry wood IBM M1 carbine stocks manufactured during WW2, I sold one for $600.00 two years ago

See more | Go to post
Leave a comment:
RCS replied to Correct Follower Arm for SA 1941/42

in Gas Trap & Pre-war Garands

01-28-2023, 09:52 PM
I posted photos on 6https://www.m1garandforum.com/filedata/fetch?id=29818-10-21...

See more | Go to post
Leave a comment:
RCS started a topic Winchester Lend Lease rifle

in WW2 Garands

01-20-2023, 07:12 PM
Winchester Lend Lease rifle

On www.milsurps/Garand forum is a Winchester s/n 149521 with BNP proof on the barrel at the rear, plus the BNP stamp on the receiver ring and near the...

See more | Go to post
RCS replied to WRA beauties

in WW2 Garands

01-15-2023, 08:43 AM
Really nice Winchester rifle photos, unable to tell if the stocks are no trap butt plates ? Collectors have stated that Winchester must have deluxe...

See more | Go to post
Likes 4
Leave a comment:
RCS replied to M1 Garand reciever line

in WW2 Garands

01-13-2023, 10:04 AM
not too many receiver tangs with this flaw, Dave McClain once told me he had seen another years ago. I use to think that maybe the firing pin pocket...

See more | Go to post
Leave a comment:
RCS started a topic late revision 1 bolt from 1940

in Gas Trap & Pre-war Garands

01-13-2023, 09:55 AM
late revision 1 bolt from 1940

The later revision 1 bolts had the drawing number and revision 1 all stamped on a single line,

The rare variation is D28287-1-SA ...

See more | Go to post
RCS replied to early follower

in Gas Trap & Pre-war Garands

01-12-2023, 11:37 AM
The photo in my post first appeared on the old jouster forum on 2/20/04 posted by Jeff S. He was looking for information about this follower with the...

See more | Go to post
Leave a comment:
RCS started a topic M4 Imperial bayonet

in Edged Weaponry

01-12-2023, 09:10 AM
M4 Imperial bayonet

Had this bayonet for a long time, believe it is WW2 manufactured ...

See more | Go to post
RCS started a topic early follower

in Gas Trap & Pre-war Garands

01-09-2023, 03:16 PM
early follower

I found this photo some years ago from another forum, note the long nose slide, but what is really odd is the notch on the front of the follower. Anyone...

See more | Go to post
Likes 3
RCS replied to Numbered Buttplate

in Gas Trap & Pre-war Garands

01-05-2023, 05:52 PM
Springfield Sporters in PA sold your type of flat butt plate they were manufactured for some countries in central and south America....

See more | Go to post
Leave a comment:
RCS replied to Identify these stacking swivels

in Battle Rifles

01-04-2023, 08:55 AM
mere is a ohoto of the early 1903 rod bayonet stacking swivel...

See more | Go to post
Likes 1
Leave a comment:
RCS started a topic Wisconsin barn wood stocks

in Gas Trap & Pre-war Garands

01-03-2023, 12:17 PM
Wisconsin barn wood stocks

Might as well post on here as the other websites all have the storyhttp://photos.imageevent.com/badgerd...s/Sp09%20Barn%...

See more | Go to post
Likes 1
RCS replied to Numbered Buttplate

in Gas Trap & Pre-war Garands

01-02-2023, 10:00 PM
the butt plate in your from came from South America, these have been around years ago, nothing related to US Military. These are made to fit the later...

See more | Go to post
Likes 1
Leave a comment: